If You Power Down a Honeywell 5200 and Power It Up Again
Yous can get into Honeywell L5200 or L5210 programming if you're locked out by powering the system down and holding down the panel's home button while reapplying power. Y'all will then perform a specific sequence of commands to get dorsum into programming. This is is chosen the backdoor method.
Y'all should only perform the backdoor method for accessing programming if you lot are indeed locked out of programming. Both the L5200 and L5210 enter programming in the same manner. From the main screen of the L5200 or L5210, choose Security > More > Tools > Installer Code (default 4112) > Program. If yous are taken to the System Programming screen, then you are not locked out of programming. Make certain to always choose "Aye" when asked if yous want to "allow the Installer to re-enter programming?" as you lot exit programming to prevent being locked out in the future. Just if nothing happens when you click "Plan", then y'all are locked out of programming, and you must use the backdoor method to get in.
The nearly mutual reason to become locked out of programming is considering the selection "NO" was chosen when asked if the Installer should be allowed to re-enter programming. Ever choose "Yes" at that screen to prevent beingness locked out. Some other common reason to be locked out of programming is because y'all accept lost the Installer Code. This consequence can exist prevented by keeping the system'south Installer Code at its default of 4112. Remember that the Installer Code cannot disarm the system unless it was the code used to originally arm. Therefore, keeping the code at its default does not represent a security risk. You tin can larn more than most keeping the IC at its default in this FAQ.
The backdoor method for inbound programming is the aforementioned for both the Honeywell L5200 and the Honeywell L5210. Complete the post-obit steps to backdoor into an L5200 or L5210:
one. Reboot the panel. The easiest style to reboot an L5200 or L5210 is to choose the selection inside the Chief Tools Menu. From the main screen, select Security > More > Tools > Main Code (default 1234) > Test > Reboot > Yes. The system will begin its rebooting process.
However, it's possible that yous might not know the Master Code for the system. If that'southward the case, then you must perform a difficult reboot. Open up up the panel, and unplug the backup battery from its port. This will cause a embrace tamper condition. Press the touchscreen, or the Home Key beneath the touchscreen to silence the trouble beeping. Continue the panel open so that you can reconnect the fill-in bombardment later. You can complete the residue of this procedure with the panel still open.
In one case the battery has been disconnected, unplug the console's transformer from the wall outlet. The transformer should be secured to the outlet with a screw. If so, you will need a screwdriver to perform this footstep. This volition power down the console completely. Wait a few seconds, and plug the transformer dorsum in to begin rebooting the system.
ii. Brainstorm the backstairs procedure. Every bit soon equally the panel lights up, printing and agree downward the Dwelling button on the front of the console, below the touchscreen. You will exist required to hold down this button for several moments. Keep belongings as the bulletin "System Standby" appears. In one case yous meet the peak bar plough light-green with the message "Ready to Arm", or turn yellow with the message "Non Ready to Arm", then you lot can release the home button. This will begin the backdoor process.
3. Clear the lockout. After you release the dwelling button, you must very speedily printing "Security", followed by "Arm Stay". If the process was performed correctly, a numeric keypad will appear on the touchscreen. Once this happens, click "Articulate", followed by "00". You volition then enter the Installer Tools Menu. And then cull "Program" to enter the programming menu.
4. Don't become locked out! Now that you lot are in programming, yous don't want to go locked out over again. If necessary, modify the Installer Code to the default of 4112 so that you can easily look up the lawmaking if you need to. Then use the return arrow in the upper-correct corner to exit programming. When asked if the Installer should be allowed to re-enter programming, choose "YES". If you do not choose "Aye", then yous will become locked out of programming once more, and you volition need to perform the backdoor method over again.
Likewise, if you had to perform a hard reboot, remember to reconnect the fill-in bombardment and close the panel once yous accept finished performing the backdoor method to access programming. Disarm the system twice to clear the comprehend tamper trouble. And remember to reapply the gear up screw for the transformer if y'all removed it before.
Source: https://www.alarmgrid.com/faq/how-do-i-get-back-into-programming-if-i-am-locked-out-on-my-l520
0 Response to "If You Power Down a Honeywell 5200 and Power It Up Again"
Post a Comment